[FW-nat-policy-interzone-trust-untrust-outbound-0]policysource 10.0.2.0 0.0.0.2

55

14:14:26 2014/07/08

[FW-nat-policy-interzone-trust-untrust-outbound-0]actionsource-nat

14:14:37 2014/07/08

[FW-nat-policy-interzone-trust-untrust-outbound-0]easy-ipg0/0/0

14:14:51 2014/07/08

[FW-nat-policy-interzone-trust-untrust-outbound-0]q

         配置完成后，驗證Trust區域與Untrust區域之間的訪問是否正常。

<R2>ping 10.0.1.1

 PING 10.0.1.1: 56  data bytes,press CTRL_C to break

   Request time out

   Request time out

   Request time out

   Request time out

   Request time out

 

  ---10.0.1.1 ping statistics ---

    5packet(s) transmitted

    0packet(s) received

   100.00% packet loss

 

<R2>ping -a 10.0.2.2 10.0.1.1

 PING 10.0.1.1: 56  data bytes,press CTRL_C to break

   Reply from 10.0.1.1: bytes=56 Sequence=1 ttl=254 time=220 ms

   Reply from 10.0.1.1: bytes=56 Sequence=2 ttl=254 time=100 ms

   Reply from 10.0.1.1: bytes=56 Sequence=3 ttl=254 time=100 ms

   Reply from 10.0.1.1: bytes=56 Sequence=4 ttl=254 time=120 ms

   Reply from 10.0.1.1: bytes=56 Sequence=5 ttl=254 time=440 ms

 

  ---10.0.1.1 ping statistics ---

    5packet(s) transmitted

    5packet(s) received

   0.00% packet loss

   round-trip min/avg/max = 100/196/440 ms

         注意，這里直接測試與10.0.1.1之間的連通性，顯示不通。使用擴展ping，指定了發送數據包的源地址是10.0.2.2后，實現了連通性。原因是，直接發送數據包到10.0.1.1時，數據包的源地址到10.0.1.1時，數據包的源地址為10.0.20.2，該地址不屬于NAT轉換的客戶端地址范圍。

步驟六.將內網服務器10.0.3.3發布出去

         配置內網服務器10.0.3.3的telnet服務，映射到地址10.0.10.20

[FW]nat server protocol tcp global10.0.10.20 telnet inside 10.0.3.3 telnet

 

         在R3上開啟Telnet功能，并在R1上測試，測試時需要注意，對外發布的地址為10.0.10.20，所以R1對10.0.3.3訪問時，訪問的目標地址為10.0.10.20。

[R3]user-interface vty 0 4

[R3-ui-vty0-4]authentication-mode password

Please configure the login password(maximum length 16):16

[R3-ui-vty0-4]set authentication password ?

 cipher  Set the password withcipher text

[R3-ui-vty0-4]set authentication passwordcip       

[R3-ui-vty0-4]set authentication passwordcipher Huawei

[R3-ui-vty0-4]user privilege level 3

[R3-ui-vty0-4]q

 

<R1>telnet 10.0.10.20

 Press CTRL_] to quit telnet mode

 Trying 10.0.10.20 ...

 Connected to 10.0.10.20 ...

 

Login authentication

本文出自 “思科實驗linux” 博客，請務必保留此出處http://1054054.blog.51cto.com/1044054/1437509

最新評論