華為HCIP認證無線技術——VRRP配置實驗案例分析

發布時間：2020-06-05 14:37:28 作者：壞壞-5

這篇文章主要介紹了華為HCIP認證無線技術——VRRP配置實驗,結合具體實驗案例形式分析了華為HCIP認證無線VRRP配置相關原理、配置命令與相關操作注意事項,需要的朋友可以參考下

本文講述了華為HCIP認證無線技術——VRRP配置實驗案例。分享給大家供大家參考，具體如下：

文章目錄

實驗拓?fù)?/a>

基礎配置
配置VRRP
實驗結果

實驗拓?fù)?/h2>

基礎配置

配置SW1

# 創建vlan，配置鏈路聚合
[SW1]vlan batch 10 20 
[SW1]int Eth-Trunk 1
[SW1-Eth-Trunk1]trunkport GigabitEthernet 0/0/10 0/0/11
[SW1-Eth-Trunk1]port link-type trunk 
[SW1-Eth-Trunk1]port trunk allow-pass vlan all 
[SW1-Eth-Trunk1]q
# 配置接口類型
[SW1]int g0/0/1 
[SW1-GigabitEthernet0/0/1]port link-type trunk 
[SW1-GigabitEthernet0/0/1]port trunk allow-pass vlan all 
[SW1-GigabitEthernet0/0/1]int g0/0/2
[SW1-GigabitEthernet0/0/2] port link-type trunk
[SW1-GigabitEthernet0/0/2] port trunk allow-pass vlan 2 to 4094
[SW1-GigabitEthernet0/0/2]q

配置SW2

# SW2創建vlan，配置鏈路聚合
[SW2]vlan batch 10 20 
[SW2]int Eth-Trunk 1
[SW2-Eth-Trunk1]trunkport GigabitEthernet 0/0/10 0/0/11
[SW2-Eth-Trunk1]port link-type trunk 
[SW2-Eth-Trunk1]port trunk allow-pass vlan all 
[SW2-Eth-Trunk1]q
# SW2配置接口類型
[SW2]int g0/0/1 
[SW2-GigabitEthernet0/0/1]port link-type trunk 
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all 
[SW2-GigabitEthernet0/0/1]int g0/0/2
[SW2-GigabitEthernet0/0/2] port link-type trunk
[SW2-GigabitEthernet0/0/2] port trunk allow-pass vlan 2 to 4094
[SW2-GigabitEthernet0/0/2]q

配置SW3、SW4

# SW3配置
[SW3]vlan ba 10 20
[SW3]int g0/0/2
[SW3-GigabitEthernet0/0/2]port link-type trunk
[SW3-GigabitEthernet0/0/2] port trunk allow-pass vlan 2 to 4094
[SW3-GigabitEthernet0/0/2]int g0/0/
[SW3-GigabitEthernet0/0/3]port link-type trunk
[SW3-GigabitEthernet0/0/3] port trunk allow-pass vlan 2 to 4094
[SW3-GigabitEthernet0/0/3]q
[SW3]int g0/0/1
[SW3-GigabitEthernet0/0/1]port link-type access 
[SW3-GigabitEthernet0/0/1]port default vlan 10

# SW4配置
[SW4]vlan ba 10 20
[SW4]int g0/0/2
[SW4-GigabitEthernet0/0/2]port link-type trunk
[SW4-GigabitEthernet0/0/2] port trunk allow-pass vlan 2 to 4094
[SW4-GigabitEthernet0/0/2]int g0/0/3
[SW4-GigabitEthernet0/0/3]port link-type trunk
[SW4-GigabitEthernet0/0/3] port trunk allow-pass vlan 2 to 409
[SW4]int g0/0/1
[SW4-GigabitEthernet0/0/1]port link-type access 
[SW4-GigabitEthernet0/0/1]port default vlan 20

AR1配置

[AR1]int g0/0/0
[AR1-GigabitEthernet0/0/0]ip ad 10.1.1.1 24
[AR1-GigabitEthernet0/0/0]q
[AR1]ip route-static 0.0.0.0 0 10.1.1.254  //配置靜態路由，否則無法互通

配置VRRP

SW1配置

# 配置vlanif的IP地址，配置VRRP
[SW1]int Vlanif 10
[SW1-Vlanif10]ip ad 10.1.1.2 24
[SW1-Vlanif10]vrrp vrid 1 virtual-ip 10.1.1.254  //配置VRID 1的虛擬網關為10.1.1.254
[SW1-Vlanif10]vrrp vrid 1 priority 120  //配置VRID 1的優先級
[SW1-Vlanif10]q
[SW1]int Vlanif 20
[SW1-Vlanif20]ip ad 20.1.1.2 24
[SW1-Vlanif20]vrrp vrid 2 virtual-ip 20.1.1.254  //配置VRID 2的虛擬網關為20.1.1.254

SW2配置

[SW2]int Vlanif 10
[SW2-Vlanif10]ip ad 10.1.1.3 24
[SW2-Vlanif10]vrrp vrid 1 virtual-ip 10.1.1.254
[SW2-Vlanif10]q
[SW2]int Vlanif 20
[SW2-Vlanif20]ip ad 20.1.1.3 24
[SW2-Vlanif20]vrrp vrid 2 virtual-ip 20.1.1.254
[SW2-Vlanif20]vrrp vrid  2 priority 120  //配置VRID 2的優先級為120