Keepalived+HAProxy實現MySQL高可用負載均衡的配置
Keepalived
由于在生產環境使用了mysqlcluster,需要實現高可用負載均衡,這里提供了keepalived+haproxy來實現.
keepalived主要功能是實現真實機器的故障隔離及負載均衡器間的失敗切換.可在第3,4,5層交換.它通過VRRPv2(Virtual Router Redundancy Protocol) stack實現的.
Layer3:Keepalived會定期向服務器群中的服務器.發送一個ICMP的數據包（既我們平時用的Ping程序）,如果發現某臺服務的IP地址沒有激活，Keepalived便報告這臺服務器失效，并將它從服務器群中剔除，這種情況的典型例子是某臺服務器被非法關機。Layer3的方式是以服務器的IP地址是否有效作為服務器工作正常與否的標準。
Layer4:主要以TCP端口的狀態來決定服務器工作正常與否。如web server的服務端口一般是80，如果Keepalived檢測到80端口沒有啟動，則Keepalived將把這臺服務器從服務器群中剔除。
Layer5:在網絡上占用的帶寬也要大一些。Keepalived將根據用戶的設定檢查服務器程序的運行是否正常，如果與用戶的設定不相符，則Keepalived將把服務器從服務器群中剔除。
Software Design
keepalived啟動后會有單個進程
8352 ? Ss 0:00 /usr/sbin/keepalived 8353 ? S 0:00 \_ /usr/sbin/keepalived 8356 ? S 0:01 \_ /usr/sbin/keepalived
父進程:內存管理,子進程管理等等
子進程:VRRP子進程
子進程:Healthchecking 子進程
實例
2臺mysqlcluster 10.1.6.203 master 10.1.6.205 backup
vip 10.1.6.173
目的訪問10.1.6.173 3366端口 分別輪詢通過haproxy轉發到10.1.6.203 3306 和10.1.6.205 3306
mysqlcluster搭建參照之前博客,這里在2臺機上安裝keepalived
root@10.1.6.203:~# apt-get install keepalived
root@10.1.6.203:~# cat /etc/keepalived/keepalived.conf
vrrp_script chk_haproxy {
script "killall -0 haproxy" # verify the pid existance
interval 2 # check every 2 seconds
weight -2 # add 2 points of prio if OK
}
vrrp_instance VI_1 {
interface eth1 # interface to monitor
state MASTER
virtual_router_id 51 # Assign one ID for this route
priority 101 # 101 on master, 100 on backup
nopreempt
debug
virtual_ipaddress {
10.1.6.173
}
track_script { #注意大括號空格
chk_haproxy
}
notify_master /etc/keepalived/scripts/start_haproxy.sh #表示當切換到master狀態時,要執行的腳本
notify_fault /etc/keepalived/scripts/stop_keepalived.sh #故障時執行的腳本
notify_stop /etc/keepalived/scripts/stop_haproxy.sh #keepalived停止運行前運行notify_stop指定的腳本 }
VRRPD配置包括三個類:
- VRRP同步組(synchroization group)
- VRRP實例(VRRP Instance)
- VRRP腳本
這里使用了 VRRP實例, VRRP腳本
注意配置選項:
stat:指定instance(Initial)的初始狀態，就是說在配置好后，這臺服務器的初始狀態就是這里指定的，但這里指定的不算，還是得要通過競選通過優先級來確定，里如果這里設置為master，但如若他的優先級不及另外一臺，那么這臺在發送通告時，會發送自己的優先級，另外一臺發現優先級不如自己的高，那么他會就回?fù)屨紴閙aster
- interface：實例綁定的網卡，因?yàn)樵谂渲锰摂MIP的時候必須是在已有的網卡上添加的
- priority 101：設置本節點的優先級，優先級高的為master
- debug：debug級別
- nopreempt:設置為不搶占
vrrp_script chk_haproxy {
script "killall -0 haproxy" # verify the pid existance
interval 2 # check every 2 seconds 腳本執行間隔
weight -2 # add 2 points of prio if OK 腳本結果導致的優先級變更：2表示優先級+2；-2則表示優先級-2
}
然后在實例(vrrp_instance)里面引用，有點類似腳本里面的函數引用一樣：先定義，后引用函數名
track_script {
chk_haproxy
}
注意：VRRP腳本(vrrp_script)和VRRP實例(vrrp_instance)屬于同一個級別
root@10.1.6.203:scripts# cat start_haproxy.sh
#!/bin/bash
sleep 5
get=`ip addr |grep 10.1.6.173 |wc -l`
echo $get >> /etc/keepalived/scripts/start_ha.log
if [ $get -eq 1 ]
then
echo "`date +%c` success to get vip" >> /etc/keepalived/scripts/start_ha.log
/usr/local/sbin/haproxy -f /etc/haproxy/haproxy.cfg
else
echo "`date +%c` can not get vip" >> /etc/keepalived/scripts/start_ha.log
fi
root@10.1.6.203:scripts# cat stop_keepalived.sh
#!/bin/bash
pid=`pidof keepalived`
if [ $pid == "" ]
then
echo "`date +%c` no keepalived process id" >> /etc/keepalived/scripts/stop_keep.log
else
echo "`date +%c` will stop keepalived " >> /etc/keepalived/scripts/stop_keep.log
/etc/init.d/keepalived stop
fi
/etc/init.d/keepalived stop
root@10.1.6.203:scripts# cat stop_haproxy.sh
#!/bin/bash
pid=`pidof haproxy`
echo "`date +%c` stop haproxy" >> /etc/keepalived/scripts/stop_ha.log
kill -9 $pid
同理配置10.1.6.205
root@10.1.6.205:~# cat /etc/keepalived/keepalived.conf
vrrp_script chk_haproxy {
script "killall -0 haproxy" # verify the pid existance
interval 2 # check every 2 seconds
weight 2 # add 2 points of prio if OK
}
vrrp_instance VI_1 {
interface eth1 # interface to monitor
state BACKUP
virtual_router_id 51 # Assign one ID for this route
priority 100 # 101 on master, 100 on backup
virtual_ipaddress {
10.1.6.173
}
track_script {
chk_haproxy
}
notify_master /etc/keepalived/scripts/start_haproxy.sh
notify_fault /etc/keepalived/scripts/stop_keepalived.sh
notify_stop /etc/keepalived/scripts/stop_haproxy.sh
}
HAProxy
下面再介紹下haproxy
HAProxy是一款基于TCP(第四層)和HTTP(第七層)應用的代理軟件,它也可作為負載均衡器.可以支持?jǐn)?shù)以萬計的并發連接.同時可以保護服務器不暴露到網絡上,通過端口映射.它還自帶監控服務器狀態的頁面.
安裝haproxy
wget -O/tmp/haproxy-1.4.22.tar.gz http://haproxy.1wt.eu/download/1.4/src/haproxy-1.4.22.tar.gz tar xvfz /tmp/haproxy-1.4.22.tar.gz -C /tmp/ cd /tmp/haproxy-1.4.22 make TARGET=linux26 make install
haproxy需要對每一個mysqlcluster服務器進行健康檢查
1.在2臺主機分別配置haproxy.cfg
root@10.1.6.203:scripts# cat /etc/haproxy/haproxy.cfg
global
maxconn 51200 #默認最大連接數
#uid 99
#gid 99
daemon #以后臺形式運行haproxy
#quiet
nbproc 1 #進程數量(可以設置多個進程提高性能)
pidfile /etc/haproxy/haproxy.pid #haproxy的pid存放路徑,啟動進程的用戶必須有權限訪問此文件
defaults
mode tcp #所處理的類別 (#7層 http;4層tcp )
option redispatch #serverId對應的服務器掛掉后,強制定向到其他健康的服務器
option abortonclose #當服務器負載很高的時候，自動結束掉當前隊列處理比較久的連接
timeout connect 5000s #連接超時
timeout client 50000s #客戶端超時
timeout server 50000s #服務器超時
log 127.0.0.1 local0 #錯誤日志記錄
balance roundrobin #默認的負載均衡的方式,輪詢方式
listen proxy
bind 10.1.6.173:3366 #監聽端口
mode tcp #http的7層模式
option httpchk #心跳檢測的文件
server db1 10.1.6.203:3306 weight 1 check port 9222 inter 12000 rise 3 fall 3 #服務器定義,check inter 12000是檢測心跳頻率 rise 3是3次正確認為服務器可用， fall 3是3次失敗認為服務器不可用，weight代表權重
server db2 10.1.6.205:3306 weight 1 check port 9222 inter 12000 rise 3 fall 3
listen haproxy_stats
mode http
bind 10.1.6.173:8888
option httplog
stats refresh 5s
stats uri /status #網站健康檢測URL，用來檢測HAProxy管理的網站是否可以用，正常返回200，不正常返回503
stats realm Haproxy Manager
stats auth admin:p@a1SZs24 #賬號密碼
root@10.1.6.205:~$ cat /etc/haproxy/haproxy.cfg
global
maxconn 51200
#uid 99
#gid 99
daemon
#quiet
nbproc 1
pidfile /etc/haproxy/haproxy.pid
defaults
mode tcp
option redispatch
option abortonclose
timeout connect 5000s
timeout client 50000s
timeout server 50000s
log 127.0.0.1 local0
balance roundrobin
listen proxy
bind 10.1.6.173:3366
mode tcp
option httpchk
server db1 10.1.6.203:3306 weight 1 check port 9222 inter 12000 rise 3 fall 3
server db2 10.1.6.205:3306 weight 1 check port 9222 inter 12000 rise 3 fall 3
listen haproxy_stats
mode http
bind 10.1.6.173:8888
option httplog
stats refresh 5s
stats uri /status
stats realm Haproxy Manager
stats auth admin:p@a1SZs24
2.安裝xinetd
root@10.1.6.203:~# apt-get install xinetd
3.在每個節點添加xinetd服務腳本和mysqlchk端口號
root@10.1.6.203:~# vim /etc/xinetd.d/mysqlchk
# default: on
# description: mysqlchk
service mysqlchk #需要在servive定義
{
flags = REUSE
socket_type = stream
port = 9222
wait = no
user = nobody
server = /opt/mysqlchk
log_on_failure += USERID
disable = no
per_source = UNLIMITED
bind = 10.1.6.173
}
root@10.1.6.203:~# vim /etc/services
mysqlchk 9222/tcp # mysqlchk
4.編寫mysqlchk監控服務腳本
root@10.1.6.203:~# ls -l /opt/mysqlchk
-rwxr--r-- 1 nobody root 1994 2013-09-17 11:27 /opt/mysqlchk
root@10.1.6.203:~# cat /opt/mysqlchk
#!/bin/bash
#
# This script checks if a mysql server is healthy running on localhost. It will
# return:
# "HTTP/1.x 200 OK\r" (if mysql is running smoothly)
# - OR -
# "HTTP/1.x 500 Internal Server Error\r" (else)
#
# The purpose of this script is make haproxy capable of monitoring mysql properly
#
MYSQL_HOST="localhost"
MYSQL_SOCKET="/var/run/mysqld/mysqld.sock"
MYSQL_USERNAME="mysqlchkusr" #該賬戶密碼需要在mysql里添加
MYSQL_PASSWORD="secret"
MYSQL_OPTS="-N -q -A"
TMP_FILE="/dev/shm/mysqlchk.$$.out"
ERR_FILE="/dev/shm/mysqlchk.$$.err"
FORCE_FAIL="/dev/shm/proxyoff"
MYSQL_BIN="/opt/mysqlcluster/mysql-cluster-gpl-7.2.6-linux2.6-x86_64/bin/mysql"
CHECK_QUERY="select 1"
preflight_check()
{
for I in "$TMP_FILE" "$ERR_FILE"; do
if [ -f "$I" ]; then
if [ ! -w $I ]; then
echo -e "HTTP/1.1 503 Service Unavailable\r\n"
echo -e "Content-Type: Content-Type: text/plain\r\n"
echo -e "\r\n"
echo -e "Cannot write to $I\r\n"
echo -e "\r\n"
exit 1
fi
fi
done
}
return_ok()
{
echo -e "HTTP/1.1 200 OK\r\n"
echo -e "Content-Type: text/html\r\n"
echo -e "Content-Length: 43\r\n"
echo -e "\r\n"
echo -e "<html><body>MySQL is running.</body></html>\r\n"
echo -e "\r\n"
rm $ERR_FILE $TMP_FILE
exit 0
}
return_fail()
{
echo -e "HTTP/1.1 503 Service Unavailable\r\n"
echo -e "Content-Type: text/html\r\n"
echo -e "Content-Length: 42\r\n"
echo -e "\r\n"
echo -e "<html><body>MySQL is *down*.</body></html>\r\n"
sed -e 's/\n$/\r\n/' $ERR_FILE
echo -e "\r\n"
rm $ERR_FILE $TMP_FILE
exit 1
}
preflight_check
if [ -f "$FORCE_FAIL" ]; then
echo "$FORCE_FAIL found" > $ERR_FILE
return_fail;
fi
$MYSQL_BIN $MYSQL_OPTS --host=$MYSQL_HOST --socket=$MYSQL_SOCKET --user=$MYSQL_USERNAME --password=$MYSQL_PASSWORD -e "$CHECK_QUERY" > $TMP_FILE 2> $ERR_FILE
if [ $? -ne 0 ]; then
return_fail;
fi
return_ok;
測試
2個節點開啟keepalived(主節點會獲得vip,自動拉起haproxy),xinetd
root@10.1.6.203:~# ip add 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether 00:26:b9:36:0f:81 brd ff:ff:ff:ff:ff:ff inet 211.151.105.186/26 brd 211.151.105.191 scope global eth0 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:26:b9:36:0f:83 brd ff:ff:ff:ff:ff:ff inet 10.1.6.203/24 brd 10.1.6.255 scope global eth1 inet 10.1.6.173/32 scope global eth1 4: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:26:b9:36:0f:85 brd ff:ff:ff:ff:ff:ff 5: eth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:26:b9:36:0f:87 brd ff:ff:ff:ff:ff:ff root@10.1.6.203:~# netstat -tunlp | grep ha tcp 0 0 10.1.6.173:3366 0.0.0.0:* LISTEN 1042/haproxy tcp 0 0 10.1.6.203:8888 0.0.0.0:* LISTEN 1042/haproxy udp 0 0 0.0.0.0:56562 0.0.0.0:* 1042/haproxy root@10.1.6.203:~# netstat -tunlp | grep xine tcp 0 0 10.1.6.203:9222 0.0.0.0:* LISTEN 30897/xinetd root@10.1.6.203:~# ps -ef | grep haproxy root 1042 1 0 Sep17 ? 00:00:00 /usr/local/sbin/haproxy -f /etc/haproxy/haproxy.cfg
測試:
通過vip10.1.6.173 3366訪問cluster數據庫(注意賬戶dave權限需要加3個ip10.1.6.203,10.1.6.205,10.1.6.173)
root@10.1.6.203:mgm# mysql -udave -p -h 10.1.6.173 -P 3366 Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1344316 Server version: 5.5.22-ndb-7.2.6-gpl-log MySQL Cluster Community Server (GPL) Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show databases; +--------------------+ | Database | +--------------------+ | information_schema | | dave | | test | +--------------------+ 3 rows in set (0.01 sec) mysql>
手動分別使keepalive,haproxy,數據庫掛掉.vip10.1.6.173會自動漂到10.1.6.205從上，并不影響vip的訪問
通過vip,haproxy查看各節點狀態
http://10.1.6.173:8888/status
相關文章
Mysql 的存儲引擎,myisam和innodb的區別
這篇文章主要介紹了Mysql 的存儲引擎,myisam和innodb的區別,需要的朋友可以參考下2014-12-12
關于Mysql5.7及8.0版本索引失效情況匯總
這篇文章主要介紹了關于Mysql5.7及8.0版本索引失效情況匯總，具有很好的參考價值，希望對大家有所幫助。如有錯誤或未考慮完全的地方，望不吝賜教2022-08-08
這篇文章主要介紹了MySQL 兩種恢復數據的方法，幫助恢復線上數據，保證數據完整，感興趣的朋友可以了解下2020-10-10
這篇文章主要介紹了關于msyql事務隔離的相關資料，文中講解非常細致，幫助大家更好的理解和學習mysql，感興趣的朋友可以了解下2020-07-07
mysql插入中文數據變成問號的解決方案
這篇文章主要介紹了mysql插入中文數據變成問號的解決方案，具有很好的參考價值，希望對大家有所幫助。如有錯誤或未考慮完全的地方，望不吝賜教2023-04-04
在mysql中，通常使用limit做分頁，而且經常會跟order by 連用。在order by 上加索引有時候是很有幫助的，不然系統會做很多的filesort2013-02-02
這篇文章主要給大家介紹了關于MySQL實例crash的相關資料，文中通過示例代碼的非常詳細，對大家學習或者使用mysql具有一定的參考學習價值，需要的朋友們下面隨著小編來一起學習學習吧2018-12-12
mysql判斷字段是否存在的方法有很多，如使用desc命令、show columns 命令、describe 命令等等，感興趣的朋友可以參考下2014-01-01
淺談innodb的索引頁結構,插入緩沖,自適應哈希索引
下面小編就為大家?guī)?lái)一篇淺談innodb的索引頁結構,插入緩沖,自適應哈希索引。小編覺得挺不錯的，現在就分享給大家，也給大家做個參考。一起跟隨小編過來看看吧2017-03-03
全面解析MySQL?Explain如何優化SQL查詢性能
在?MySQL?中，EXPLAIN?關鍵字可以幫助我們分析查詢執行計劃，從而優化查詢性能，所以本文就來和大家詳細講講Explain是如何優化SQL查詢性能的2023-05-05