（1）首先安裝paramiko庫

pip install paramiko

（2）封裝了以下類，可以直接拿來使用

import paramiko

class SSHClient(object):
    def __init__(self,host,username,password,port=22):
        self.__host=host
        self.__username=username
        self.__password=password
        self.__port=port
        self.__ssh=None
        self.connect()

    def __del__(self):
        self.close()

    def connect(self):
        self.__ssh = paramiko.SSHClient()
        self.__ssh.set_missing_host_key_policy(paramiko.AutoAddPolicy())
        self.__ssh.connect(hostname=self.__host,port=self.__port,username=self.__username,password=self.__password)

    def exec(self,cmd):
        print(f"begin to run remote cmd: {cmd}")
        stdin, stdout, stderr = self.__ssh.exec_command(cmd,timeout=1800)
        returncode = stdout.channel.recv_exit_status()
        output=stdout.read().decode('utf-8')
        return output

    def close(self):
        self.__ssh.close()

（3）比如準備一個ip地址為192.168.1.12的linux虛擬機，然后直接按照如下方法使用上面封裝的類即可實現遠程執行l(wèi)inux命令

ssh=SSHClient(host="192.168.1.12",username="root",password="xxxxxx")
output=ssh.exec("ifconfig")
print(output)

（4）執行結果如下

begin to run remote cmd: ifconfig
ens33: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.12  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 240e:3a1:da7:6590:b39f:e15:6b3d:7e7  prefixlen 64  scopeid 0x0<global>
        inet6 fe80::4a67:131d:9133:acdf  prefixlen 64  scopeid 0x20<link>
        ether 00:0c:29:58:d8:4c  txqueuelen 1000  (Ethernet)
        RX packets 195340  bytes 148862388 (141.9 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 163425  bytes 20837281 (19.8 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 32  bytes 2592 (2.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 32  bytes 2592 (2.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

virbr0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 192.168.122.1  netmask 255.255.255.0  broadcast 192.168.122.255
        ether 52:54:00:e8:3f:5c  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

到此這篇關于Python通過paramiko庫實現遠程執行l(wèi)inux命令的文章就介紹到這了,更多相關Python遠程執行l(wèi)inux命令內容請搜索腳本之家以前的文章或繼續瀏覽下面的相關文章希望大家以后多多支持腳本之家！

最新評論