C++實現算法兩個數字相加詳解

更新時間：2021年07月09日 09:35:48 作者：Grandyang

這篇文章主要介紹了C++實現算法兩個數字相加詳解,本篇文章通過簡要的案例,講解了該項技術的了解與使用,以下就是詳細內容,需要的朋友可以參考下

Add Two Numbers 兩個數字相加

You have two numbers represented by a linked list, where each node contains a single digit. The digits are stored in reverse order, such that the 1's digit is at the head of the list. Write a function that adds the two numbers and returns the sum as a linked list.
EXAMPLE
Input: (7-> 1 -> 6) + (5 -> 9 -> 2).That is, 617 + 295.
Output: 2 -> 1 -> 9.That is, 912.
FOLLOW UP
Suppose the digits are stored in forward order. Repeat the above problem.
EXAMPLE
Input: (6 -> 1 -> 7) + (2 -> 9 -> 5).That is, 617 + 295.
Output: 9 -> 1 -> 2.That is, 912.

LeetCode上的原題，請參考另一篇文檔Add Two Numbers 兩個數字相加。

跟那道LeetCode有所不同的是，這道題還有個Follow Up，把鏈表存的數字方向變了，原來是表頭存最低位，現在是表頭存最高位。既然是翻轉了鏈表，那么一種直接的解法是把兩個輸入鏈表都各自翻轉一下，然后用之前的方法相加完成，再把得到的結果翻轉一次，就是結果了，翻轉鏈表的方法可以參考另一篇文檔Reverse Linked List 倒置鏈表。代碼如下：

解法一：

// Follow up
class Solution {
public:
    ListNode *addTwoNumbers(ListNode *l1, ListNode *l2) {
        ListNode *dummy = new ListNode(-1);
        ListNode *cur = dummy;
        int carry = 0;
        l1 = reverseList(l1);
        l2 = reverseList(l2);
        while (l1 || l2) {
            int n1 = l1 ? l1->val : 0;
            int n2 = l2 ? l2->val : 0;
            int sum = n1 + n2 + carry;
            carry = sum / 10;
            cur->next = new ListNode(sum % 10);
            cur = cur->next;
            if (l1) l1 = l1->next;
            if (l2) l2 = l2->next;
        }
        if (carry) cur->next = new ListNode(1);
        return reverseList(dummy->next);
    }
    ListNode *reverseList(ListNode *head) {
        if (!head) return head;
        ListNode *dummy = new ListNode(-1);
        dummy->next = head;
        ListNode *cur = head;
        while (cur->next) {
            ListNode *tmp = cur->next;
            cur->next = tmp->next;
            tmp->next = dummy->next;
            dummy->next = tmp;
        }
        return dummy->next;
    }
};

如果我們不采用翻轉鏈表的方法該怎么做呢，這就比較復雜了。首先我們要縣分別計算出兩個鏈表的長度，然后給稍短一點的鏈表前面補0，補到和另一個鏈表相同的長度。由于要從低位開始相加，而低位是鏈表的末尾，所以我們采用遞歸來處理，先遍歷到鏈表的末尾，然后從后面相加，進位標示符carry用的是引用，這樣保證了再遞歸回溯時值可以正確傳遞，每次計算的節點后面接上上一次回溯的節點，直到回到首節點完成遞歸。最后還是處理最高位的進位問題。代碼如下：

解法二：

// Follow up
class Solution {
public:
    ListNode *addTwoNumbers(ListNode *l1, ListNode *l2) {
        int n1 = 0, n2 = 0, carry = 0;;
        n1 = getLength(l1);
        n2 = getLength(l2);
        if (n1 > n2) l2 = padList(l2, n1 - n2);
        if (n2 > n1) l1 = padList(l1, n2 - n1);
        ListNode *res = addTwoNumbersDFS(l1, l2, carry);
        if (carry == 1) {
            ListNode *tmp = new ListNode(1);
            tmp->next = res;
            res = tmp;
        }
        return res;
    }
    ListNode *addTwoNumbersDFS(ListNode *l1, ListNode *l2, int &carry) {
        if (!l1 && !l2) return NULL;
        ListNode *list = addTwoNumbersDFS(l1->next, l2->next, carry);
        int sum = l1->val + l2->val + carry;
        ListNode *res = new ListNode(sum % 10);
        res->next = list;
        carry = sum / 10;
        return res;
    }
    ListNode *padList(ListNode *list, int len) {
        ListNode *dummy = new ListNode(-1);
        ListNode *cur = dummy;
        for (int i = 0; i < len; ++i) {
            cur->next = new ListNode(0);
            cur = cur->next;
        }
        cur->next = list;
        return dummy->next;
    }
    int getLength(ListNode *list) {
        ListNode *cur = list;
        int res = 0;
        while (cur) {
            ++res;
            cur = cur->next;
        }
        return res;
    }
};

到此這篇關于C++實現算法兩個數字相加詳解的文章就介紹到這了,更多相關C++實現兩個數字相加內容請搜索腳本之家以前的文章或繼續瀏覽下面的相關文章希望大家以后多多支持腳本之家！

您可能感興趣的文章: