# _*_coding:utf-8_*_
import time, threading, ConfigParser
 
'''
Reader類，繼承threading.Thread
@__init__方法初始化
@run方法實現了讀文件的操作
'''
class Reader(threading.Thread):
  def __init__(self, file_name, start_pos, end_pos):
    super(Reader, self).__init__()
    self.file_name = file_name
    self.start_pos = start_pos
    self.end_pos = end_pos
 
  def run(self):
    fd = open(self.file_name, 'r')
    '''
    該if塊主要判斷分塊后的文件塊的首位置是不是行首，
    是行首的話，不做處理
    否則，將文件塊的首位置定位到下一行的行首
    '''
    if self.start_pos != 0:
      fd.seek(self.start_pos-1)
      if fd.read(1) != '\n':
        line = fd.readline()
        self.start_pos = fd.tell()
    fd.seek(self.start_pos)
    '''
    對該文件塊進行處理
    '''
    while (self.start_pos <= self.end_pos):
      line = fd.readline()
      '''
      do somthing
      '''
      self.start_pos = fd.tell()
 
'''
對文件進行分塊，文件塊的數量和線程數量一致
'''
class Partition(object):
  def __init__(self, file_name, thread_num):
    self.file_name = file_name
    self.block_num = thread_num
 
  def part(self):
    fd = open(self.file_name, 'r')
    fd.seek(0, 2)
    pos_list = []
    file_size = fd.tell()
    block_size = file_size/self.block_num
    start_pos = 0
    for i in range(self.block_num):
      if i == self.block_num-1:
        end_pos = file_size-1
        pos_list.append((start_pos, end_pos))
        break
      end_pos = start_pos+block_size-1
      if end_pos >= file_size:
        end_pos = file_size-1
      if start_pos >= file_size:
        break
      pos_list.append((start_pos, end_pos))
      start_pos = end_pos+1
    fd.close()
    return pos_list
 
if __name__ == '__main__':
  '''
  讀取配置文件
  '''
  config = ConfigParser.ConfigParser()
  config.readfp(open('conf.ini'))
  #文件名
  file_name = config.get('info', 'fileName')
  #線程數量
  thread_num = int(config.get('info', 'threadNum'))
  #起始時間
  start_time = time.clock()
  p = Partition(file_name, thread_num)
  t = []
  pos = p.part()
  #生成線程
  for i in range(thread_num):
    t.append(Reader(file_name, *pos[i]))
  #開啟線程
  for i in range(thread_num):
    t[i].start()
  for i in range(thread_num):
    t[i].join()
  #結束時間
  end_time = time.clock()
  print "Cost time is %f" % (end_time - start_time)